Simple, easy to follow instructions on how to hang string lights in your backyard without trees and other structures interfering.

“How to Hang String Lights in Your Backyard Without Trees” is a blog post that will teach you how to hang string lights without trees. Read more in detail here: how to hang string lights in backyard without trees.

Lights on a string hung from the ceiling are a simple way to add a touch of enchantment to your garden. Lights on a string are fantastic since they’re simple to hang yet can make a tremendous impact in your backyard’s atmosphere. Although utilizing trees to hang Lights on a string is a common strategy, there are many more options. We’ll go through how to put Lights on a string in your backyard without trees, as well as some other helpful hints.

Contents

Option 1: Hanging Lights on a Do-It-Yourself Post

How-to-Hang-String-Lights-in-Your-Backyard-Without-Trees

If you don’t have enough trees in your garden to hang Lights on a string, you can simply make your own DIY post. What’s nice about this choice is that you can use both lights and plants to truly brighten up your yard.

This procedure seems to be time-consuming, yet it will go by far quicker than you expect. Plus, after you’re done, you’ll be able to sit back, relax, and take in your beautiful backyard.

You’ll need the following items:

  • 6 large pots of flowers
  • Spray paint in the color of your choice.
  • tarpaulin
  • 6 x 2 x 8′ 2″ x 2″ x 8′ 2″ x 2″ x 8′ 2″
  • Paint colors that go together (optional)
  • Tape for painting
  • 6 hooks for cups
  • Concrete mix in four 50-pound bags
  • Water
  • Stir with the stick
  • Level
  • Gravel is used as a drainage material.
  • Soil for pots
  • Plants
  • Outdoor Lights on a string with a length of 100 feet

Step 1: Paint the Planters and Posts

Clean the planters with a damp cloth and dry completely. Set them upside down on a tarpaulin and completely cover with spray paint. Keep applying additional layers of paint as necessary for full coverage. Once the outside layer dries, turn planters over and paint the inside of the rim.

Use painters tape to mask off the remaining 5′′ of the post and paint one end. Allow the paint to dry fully before masking the painted section and leaving approximately 1′′ of the band exposed.

Paint the remaining band with its coordinating color, allow it to dry completely, and remove the Tape for painting. Add a cup hook in the center of each post where the two colors meet.

Step 2: Pour Concrete into the Planter

Inside each of your pots, place the unpainted end of a post. Distribute the dry concrete mix evenly among the pots. To calculate the quantity of water for each planter, follow the manufacturer’s recommendations and mix with a stick until everything is properly integrated.

Use a level on one side to make the post plumb. Use Tape for painting on each side of the post to hold it in place. Once the concrete is level and the post is in place, allow the concrete to harden according to the instructions.

Step 3: Include Plants

After the concrete is completely cured, add roughly 3″ a Gravel is used as a drainage material.. Top the drainage material with Soil for pots and lightly pack it down.

You may now add any plants you want! When deciding which plants to utilize, keep the position of the posts in mind.

If you have a shaded backyard, read this article to find out which plants thrive in it.

Step 4: Attach the Lights

Place the pots in a rectangular shape with no more than 10 feet between them.

One end of the Lights on a string should be attached to one of the cup hooks. If there isn’t a hook, you may use cable or twist ties. Make an outline of your pots using the lights.

Once you’ve created a rectangle shape with Lights on a string, start zigzagging them from side to side, equally spacing them. To help this procedure go faster, put the lights on the ground underneath the rectangle to get a sense of where they should go.

As with the beginning of the light string, secure the opposite end of the cup hook. Finally, enjoy it by plugging an outdoor-safe extension cable into an outlet.

Option number two is to hang lights around the fence.

1647033772_493_How-to-Hang-String-Lights-in-Your-Backyard-Without-Trees

If you have a fence and wish to place Lights on a string in your backyard without trees, you’re in luck!

Hanging Lights on a string from your fence is a simple and easy method to add some outdoor illumination to your garden. This procedure takes few resources and may be completed by anybody with a fence.

What You’ll Require

  • A fence on which to put Lights on a string
  • Lights on a string
  • Posts of assistance
  • a can of paint (optional)
  • Mounting hooks made of metal
  • Hammer
  • Nails

Step One: Lay Out Lights on a string

Start by figuring out where your lights will get their electricity and whether or not you’ll require an outside extension cable. As you set out your lights, keep the position of the power supply in mind.

Lay your Lights on a string along the outside of the fence to give you an idea of how much length you will need and to identify where you’ll need Posts of assistance. If you have a friend or family member to help out, you could have them hold one end while you hold the other. This way, you can see exactly what they’ll look like once hung up.

Step 2: Picking Wooden Posts

Depending on the Lights on a string you choose, you’ll need a wooden post that will be strong enough to hold the lights up and protect them from outside elements. When choosing the posts, be sure that you get posts that are all the same length, size, and shape.

You may personalize the posts by painting them in the color of your choice.

Step 3: Secure the Mounting Hooks

Attaching mounting hooks properly is important in order to hold your Lights on a string. Screw the mounting hooks into the wooden post and ensure that they are in firmly.

Step 4: Put the Posts in Place

To fasten wooden posts to the fence, use a hammer and nails. Measure your posts with a tape measure to ensure that they are set at uniform heights and that your lights hang evenly.

Place the poles wherever you see fit, keeping in mind that they must be spaced far enough apart to support the lights.

Step Five: Hang the Lights on a string

After everything is in place, you may start hanging your lights! To begin, connect the lights to an outlet or an outside extension cable.

Attach the first bulb or light next to the mounting hardware to see the spacing. Unplug the lights and hang the rest of your Lights on a string.

Hang the lights on each of the fence supports as you go along the fence.

If you choose, you may use mounting hooks built into your fence to attach the lights straight to the fence.

Option Three: Hang Lights on a string Using Metal Pole

Similar to option one, this is an option that will require a little work but is worth it if you want Lights on a string in your backyard.

The fact that this option is so adjustable is a bonus. It doesn’t matter whether you have a tiny or large space for your lighting. All you have to do now is measure and set the poles where you want them!

You’ll need the following items:

  • Hacksaw
  • Drill
  • Paintbrush
  • Forms made of concrete
  • Concrete
  • PVC pipe with a diameter of 1 inch
  • 3/4-inch conduit
  • 3/4-inch end cap
  • Eyescrew
  • Nut
  • Primer
  • Paint
  • Lights on a string
  • Zip ties

Step 1: Pour the concrete

Sink Forms made of concrete at the corners of the backyard area where you’ll want to install the light supports and hang your Lights on a string. Be sure that the forms are set deep enough that they are below the frost line.

Inside, place a piece of 1′′ PVC pipe in the center and then fill the concrete around it.

Step 2: Cut the Pipes

Cut 3/4-inch conduit to the height you want your lights, plus the height of the PVC pipe already in the ground, using a hacksaw.

Drill Holes in the Third Step

Screw a 3/4″ cap onto the end with the conduit. Drill a 1″ hole below, and insert a Eyescrew through the hole. This will be where the Lights on a string will be held.

When you’re done, use a nut to hold it in place.

Step 4: Complete the Poles

Priming your pole is the first step, followed by painting it with the color of your choosing.

Make sure the concrete is completely dry before inserting the pole into the concrete’s PVC pipe.

Step 5: Connect the Lights

Now that you’re finished with the above steps, it’s time to attach your Lights on a string! Use a zip tie to attach your lights to the Eyescrew.

Spray paint the zip tie to match the color of the pole and hook to make it less obvious.

Option Four: Hang Lights on a string on Patio Ceiling

1647033774_700_How-to-Hang-String-Lights-in-Your-Backyard-Without-Trees

By now, you have a few options to hang Lights on a string in your backyard without trees, but we have one more for you!

Draping lights across the ceiling isn’t just a backyard wedding decoration. Adding Lights on a string to your patio ceiling is really simple and will look gorgeous when you’re finished.

You’ll need the following items:

  • Lights on a string
  • Hooks
  • Is it a pole or a post? (optional)
  • Planter or bucket (optional)
  • Gravel is heavy (optional)

Step 1: Look for existing resources.

There are several patterns to choose from with this choice. You could either pick a single point from which multiple light strands will extend out from your patio to other supports, or you could choose several points from which multiple light strands will reach out from your patio to other supports. Take notice of any natural patterns that exist in your garden.

There is no right or wrong way to do it, so think about how you want the finished product to appear as you go through the process.

Check your patio ceiling for existing regions that are solid enough to install your lights, then tape the spots where you’ll hang your lights.

After that, seek for alternative places to attach the lights from your patio ceiling to. Don’t worry if you don’t have many possibilities in your garden; we’ll go over another option for making your own supports later.

Here are some examples of light-supporting materials:

  • Roof
  • Deck
  • Railing
  • Fence
  • Your home’s eaves

Once you’ve determined which locations are suitable for mounting your lights, consider how you’ll hang them. You want to make sure the strands can go from point A to point B without difficulty.

Step 2: Pick a location where you’ll make your own supports.

You may discover that a few spots work well for hanging your lights, but there are a few gaps that need to be filled. In this instance, you may simply make your own hanging light supports.

Mark the spots where you’ll be making your own supports using tape.

Step 3: Obtain posts or poles from which to hang your lights.

When it comes to hanging lights, you’ll want to make sure you choose poles that are tall enough for everyone to walk or sit underneath. When deciding which poles or posts to use, keep this in mind.

You may use a metal pole for a more durable choice. If that isn’t your style, wooden poles are an excellent alternative.

You may use spray paint or other ornamental elements to make them more aesthetically attractive in any instance.

Step 4: Support the Post with a Bucket and Heavy Gravel

You may make your own supports using poles, buckets, or planters, much like option one and three above. You may use heavy gravel to keep the plants in place if you don’t want to hassle with mixing concrete and adding plants.

Arrange the buckets or pots around the perimeter of the area where your lights will be hung.

Make sure you’re comfortable with the position of your posts before adding the gravel to prevent having to shift heavy planters.

After you’ve decided on your layout, place the post in the planter. Before adding lights, make sure the post is strong once everything is in place and the bucket or planter is filled with gravel.

Step 5: Attach hooks

You’re nearly ready to hang the lights after you’ve drawn out your overall scheme.

Attach hooks to the existing supports, as well as the poles or posts, that you discovered previously. If hooks aren’t an option, zip ties may be used to secure the lights to the poles.

Step 6: Hang the Lights

To make things simpler, plan out where you’ll hang your lights before you hang them. This will also ensure that you have sufficient length before beginning.

Weave your lights from one pole to the next or to the earlier-mentioned supports. Make sure your lights are loosely hung to allow for some movement.

Last Thoughts

Hanging Lights on a string around your backyard is a simple way to add ambiance to your backyard. Although using trees is an option for some, you have plenty of options to hang Lights on a string in your backyard without trees as well. Have fun, and enjoy the process of hanging your Lights on a string! Whether you choose smaller light strands, such as fairy lights, or strands that have great big bulbs, it’s sure to add some flair to your backyard!

The “how to hang string lights in backyard with trees” is a question that has been asked many times before. There are many ways to do this, but the most common way is using wire.

Frequently Asked Questions

How do you hang string lights in your backyard?

A: Hanging string lights is a popular decoration for plants and trees. There are different ways you can go about this, but the simplest way to hang them would be with fishing wire or thick twine (i.e., butchers twine). If your yard has more ground cover than dirt, then it will help if you have something that serves as both support and grip–such as tree branches, bamboo poles, or stakes made from rebar rods

How do you hang string lights without holes?

How do you put posts in ground for string lights?

A: Using wire threaded through a piece of cardboard, or other similar material.

Related Tags

  • how to hang party lights without trees
  • pole stand for string lights
  • how to install string lights in backyard
  • post in ground for string lights
  • diy string light pole

Also Read:

    None Found